10.5.1 The syslog.conf Configuration File

The /etc/syslog.conf file controls where messages are logged. A typical syslog.conf file might look like this:

*.err;kern.debug;auth.notice /dev/console daemon,auth.notice           /var/adm/messages lpr.*                        /var/adm/lpd-errs auth.*                       root,nosmis auth.*                       @prep.ai.mit.edu *.emerg                      * *.alert                      |dectalker mark.*                       /dev/console

NOTE: The format of the syslog.conf configuration file may vary from vendor to vendor. Be sure to check the documentation for your own system.

Each line of the file contains two parts:

• A selector that specifies which kind of messages to log (e.g., all error messages or all debugging messages from the kernel).

• An action field that says what should be done with the message (e.g., put it in a file or send the message to a user's terminal).

NOTE: You must use the tab character between the selector and the action field. If you use a space, it will look the same, but syslog will not work.

Message selectors have two parts: a facility and a priority. kern.debug , for example, selects all debug messages (the priority) generated by the kernel (the facility). It also selects all priorities that are greater than debug. An asterisk in place of either the facility or the priority indicates "all." (That is, * .debug means all debug messages, while kern. * means all messages generated by the kernel.) You can also use commas to specify multiple facilities. Two or more selectors can be grouped together by using a semicolon. (Examples are shown above.)

The action field specifies one of five actions:[7]

[7] Some versions of syslog support additional actions, such as logging to a proprietary error management system.

• Log to a file or a device. In this case, the action field consists of a filename (or device name), which must start with a forward slash (e.g., /var/adm/lpd-errs or /dev/console). [8]

  [8] Beware: logging to /dev/console creates the possibility of a denial of service attack. If you are logging to the console, an attacker can flood your console with log messages, rendering it unusable.

• Send a message to a user. In this case, the action field consists of a username (e.g., root ). You can specify multiple usernames by separating them with commas (e.g., root,nosmis ). The message is written to each terminal where these users are shown to be logged in, according to the utmp file.

• Send a message to all users. In this case, the action field consists of an asterisk (e.g., *).

• Pipe the message to a program. In this case, the program is specified after the UNIX pipe symbol (|). [9]

  [9] Some versions of syslog do not support logging to programs.

• Send the message to the syslog on another host. In this case, the action field consists of a hostname, preceded by an at sign (e.g., @prep.ai.mit.edu . ).

With the following explanation, understanding the typical syslog.conf configuration file as shown earlier becomes easy.

*.err;kern.debug;auth.notice /dev/console

This line causes all error messages, all kernel debug messages, and all notice messages generated by the authorization system to be printed on the system console. If your system console is a printing terminal, this process will generate a permanent hardcopy that you can file and use for later reference. (Note that kern.debug means all messages of priority debug and above.)

daemon,auth.notice /var/adm/messages

This line causes all notice messages from either the system daemons or the authorization system to be appended to the file /var/adm/messages .

Note that this is the second line that mentions auth.notice messages. As a result, auth.notice messages will be sent to both the console and the messages file.

lpr.* /var/adm/lpd-errs

This line causes all messages from the line printer system to be appended to the /var/adm/lpd-errs file.

auth.* root,nosmis

This line causes all messages from the authorization system to be sent to the users root and nosmis . Note, however, that if the users are not logged in, the messages will be lost.

auth.* @prep.ai.mit.edu

This line causes all authorization messages to be sent to the syslog daemon on the computer prep.ai.mit.edu . If you have a cluster of many different machines, you may wish to have them all perform their loggings on a central (and presumably secure) computer.

*.emerg *

This line causes all emergency messages to be displayed on every user's terminal.

*.alert |dectalker

This line causes all alert messages to be sent to a program called dectalker , which might broadcast the message over a public address system.

mark.* /dev/console

This line causes the time to be printed on the system console every 20 minutes. This is useful if you have other information being printed on the console and you want a running clock on the printout.

NOTE: By default, syslog will accept log messages from arbitrary hosts sent to the local syslog UDP port. This can result in a denial of service attack when the port is flooded with messages faster than the syslog daemon can process them. Individuals can also log fraudulent messages. You must properly screen your network against outside log messages.

10.5.2 Where to Log

Because the syslog facility provides many different logging options, this gives individual sites flexibility in setting up their own logging. Different kinds of messages can be handled in different ways. For example, most users won't want to be bothered with most log messages. On the other hand, auth.crit messages should be displayed on the system administrator's screen (in addition to being recorded in a file). This section describes a few different approaches.

10.5.3 syslog Messages

The following tables[11] summarize some typical messages available on various versions of UNIX .:

[11] A similar list is not available for System V UNIX, because syslog is part of the Berkeley UNIX offering. Companies that sell syslog with their System V offerings may or may not have modified the additional programs in their operating systems to allow them to use the syslog logging facility.

Other critical conditions that might be present might include messages about full filesystems, device failures, or network problems.

NOTE: For security reasons, some information should never be logged. For example, although you should log failed password attempts, you should not log the password that was used in the failed attempt. Users frequently mistype their own passwords, and logging these mistyped passwords would help a computer cracker break into a user's account. Some system administrators believe that the account name should also not be logged on failed login attempts - especially when the account typed by the user is nonexistent. The reason is that users occasionally type their passwords when they are prompted for their usernames. If invalid accounts are logged, then it might be possible for an attacker to use those logs to infer people's passwords.

You may want to insert syslog calls into your own programs to record information of importance. Third-party software also often has a capability to send log messages into the syslog if configured correctly. For example, Xyplex terminal servers and Cisco routers both can log information to a network syslog daemon; Usenet news and POP mail servers also log information.

If you are writing shell scripts, you can also log to syslog . Usually, systems with syslog come with the logger command. To log a warning message about a user trying to execute a shell file with invalid parameters, you might include:

logger -t ThisProg -p user.notice "Called without required # of parameters"

NOTE: Prior to 1995, many versions of the syslog library call did not properly check their inputs to be certain that the data would fit into the function's internal buffers. Thus, many programs could be coerced to accept input to write arbitrary data over their stacks, leading to potential compromise. Be certain that you are running software using a version of syslog that does not have this vulnerability.