22. Security

Contents:
Why root?
The Environment
SMTP Probes
The Configuration File
Permissions
The Aliases File
Forged Mail
Security Features
Pitfalls

The sendmail program can be an open door to abuse. Unless the administrator is careful, the misuse or misconfiguration of sendmail can lead to an insecure and possibly compromised system. Since sendmail is usually installed to run as an suid root process, it is a prime target for intrusion. The "Internet worm," for example, used a flaw in old versions of sendmail as one way to gain entry to thousands of machines. [1] If sendmail is not properly installed, external probes over networks can be used to gain information that is valuable in attempting entry. Once inside, improper file permissions can be used to trick sendmail into giving away root privilege. Even email cannot be trusted, and forged email can cause some users to give away their passwords.

[1] That flaw has been eliminated - wrongly by some vendors who turned all debugging completely off correctly by most who simply disabled SMTP debugging.

In this chapter we present several ways to protect your site from intrusion via sendmail . Most are just good common sense, and the experienced system administrator may be offended that we state the obvious. But not all system administrators are experienced, and not all who administer systems are system administrators. If you fall into the latter category, you may wish to keep keep a good, general UNIX reference by your side to better appreciate our suggestions.

22.1 Why root?

One common complaint about sendmail centers on the fact that it must usually be run suid root (that is, run as root no matter who actually runs it). [2] But for the most part it is necessary for sendmail to run as root to satisfy the legitimate needs of users. Consider the following:

[2] Contrary to popular belief, sendmail does not run as root to handle local delivery (except that sendmail can deliver directly to files when necessary, but that is not directly germane to this discussion). Local delivery is handled by delivery agents (such as /bin/mail ), which may run suid root themselves (or sgid mail as in SysV).

Users want ~/.forward files to work even when their home directory is set to mode 700. The sendmail program requires root privilege so that it can temporarily become the user to read and process the ~/.forward file.
Users want :include: mailing-list files readable only by themselves and sendmail . The sendmail program requires root privilege so that it can temporarily become the owner of the list.
Users want programs that run on their behalf to run as themselves. This requires root privileges, and running as anything else would be potentially very dangerous.
Users want sendmail to listen on a TCP/IP port that is common (port 25). The sendmail program requires root privilege so that it can initiate a listening connection to its privileged port.

Some folks have been tempted to run sendmail as an untrusted pseudo-user (such as nobody ). But this doesn't really work. For example, it causes programs in users' ~/.forward files to be run as nobody , and it requires the queue to be owned by nobody . Consequently, such a scheme allows any user to break into and modify the queue. [3]

[3] But note that V8.8 sendmail has loosened the latter for use on firewall machines, where it won't complain about non- root qf files if it is not running as root .

22.1.1 Test seteuid and setreuid

Clearly, many of sendmail 's duties require it to run as root . As a corollary, however, whenever sendmail does not need to be root , it should become the appropriate nonprivileged user. It does this by using the following bit of logic:

If it was compiled with support for seteuid (3) (see Section 18.8.55, USESETEUID ), use that routine to set the effective uid to that of the desired non- root user. This is less preferred than the following:
If it was compiled with support for setreuid (3) (see Section 18.8.9, HAS... ), use that routine to set the effective and real uid s to those of the desired non- root user.
Otherwise, use setuid (3) to become the desired non- root user.

Note that setreuid (3) is preferred over seteuid (3) [4] and setuid (3) because it allows sendmail to temporarily give away both its real and effective root privilege, then to get it back again. To illustrate the need for this behavior, consider processing a mailing list that saves mail to two different files:

[4] Except when seteuid (3) is Posix compliant. Old implementations of seteuid (3) didn't properly save the uid ; hence the preference, in that, case for setreuid (3).

/u/bill/archive        
 owned by the user bill, mode 4600
 /u/alice/archive       
 owned by the user alice, mode 4600

Further consider that these files both have permissions of suid to the individual users [5] and are writable only by the individual users. To perform delivery in this instance, sendmail must [6] first become bill (this requires root privilege to do). When it is done, sendmail must become root again so that it can next become alice . By retaining a real uid of root (with the seteuid (3) routine), sendmail is able to change its effective uid back and forth between users and root as needed.

[5] When delivering to files, sendmail will become the owner of the file if that file's suid bit is set and if no execute bits are set.

[6] We say "must" because in an NFS environment, root is mapped to nobody so, in that instance, even root won't be able to write to bill 's files.

See the description of the test directory in Section 18.8.55 for more on this subject.